SPACE PLANNING
Planning Guides
General spacing and sizing guidelines for seating, booths, and tables. Confirm final layouts and code requirements with your architect or designer.
Chair Spacing
- Wait-staff aisles: approximately 24 to 48 inches, depending on traffic and use.
- Banquet or close seating: 8–12 square feet per person.
- Casual dining: 10–12 square feet per person.
- Spacious dining: 12–14 square feet per person.
Chair and Barstool Heights
ABC targets approximately an 18-inch dining-chair seat height; individual styles may range from approximately 17 to 19.5 inches. ABC targets approximately a 30-inch barstool seat height; individual styles may range from approximately 29 to 31 inches. Upholstery method can change the final seat height.
Booth Types and Spacing
- Common formats: deuce, single, double, half circle, three-quarter circle, wall bench, waiting bench, corner, and custom banquette.
- Preliminary booth allowance: approximately 6 square feet per person.
- Standard top cap on singles and doubles: 2 inches.
- With a 30-inch table, booth top-cap centers are typically 72 inches apart.
- With a 24-inch table, top-cap centers may be reduced to approximately 66 inches.
Standard Booth Footprints
| Format | Catalog footprint |
|---|---|
| Deuce single or double | 30-inch length |
| Single or double | 48-inch length |
| Half circle | 48 × 88 × 48 inches |
| Three-quarter circle | 48 × 88 × 88 × 48 inches |
| Standard back heights | 36, 42, and 48 inches |
For upholstered booths installed between walls, partitions, under ledges, or within other tight conditions, allow at least ½ inch of dimensional variation.
Three-Piece Base Recommendations
| Table top | Recommended base |
|---|---|
| 24 round; 24 × 24; 24 × 30 | TB2222 or TB18R |
| 24 × 42 | TB2230 |
| 24 × 48 | Two TB0522 bases or TB2230 |
| 30 round; 30 × 30 | TB2222 or TB24R |
| 30 × 42; 30 × 45 | TB2230 |
| 30 × 48 | Two TB0522 bases or TB2230 |
| 36 round; 36 × 36 | TB3030 or TB30R |
| 36 × 48 | Two TB0522 bases or TB2230 |
| 36 square opening to 51 round | TB3636 |
| 30 × 72 | Two or three TB0522 bases |
| 42 round; 42 × 42; 48 round | TB3636 |
| 60 round | Three TB0522 bases |
Cantilever Base Recommendations
| Table top | Recommended base |
|---|---|
| 24 × 30 | TBCL28 |
| 24 × 48 | TBCL33; optional pin leg |
| 30 × 30 | TBCL28 |
| 30 × 45 | TBCL33 |
| 30 × 48 | TBCL33; optional pin leg |
| 30 × 60; 30 × 72 | TBCL33 with pin leg |
Table Top Planning Notes
- Standard tops are offered through 72 inches long.
- Longer tops may be considered, but cannot be warranted against warping.
- Booth-cut and special-corner cuts are available on qualifying constructions.
- Confirm finish, edge, corner radius, thickness, base placement, mounting requirements, accessibility, unusual loads, overhangs, and floor conditions before ordering.
Routine Seating Maintenance
Inspect wood seating and non-fully-welded metal seating at least monthly. Tighten loose fasteners and remove damaged furniture from use until repaired.
